A-1 Cardone 19-272 - Brake Caliper
- Part Number
- 19-272
- Manufacturer
- A-1 CARDONE
- Description
-
Brake Caliper
details
We cannot fulfill orders for this part at this time. Please check back later or request a stock notification to receive an email.
Sometimes we may have similar parts for sale, click the button below to see if anything matches.
A-1 CARDONE part description
Product Description
Brake Caliper
Application Summary
Mercedes-Benz 190C 1965-63, 190DC 1965-63, 200 1967-66, 200D 1968-66, 220 1973-68, 220D 1973-68, 220S 1965-63, 220Sb 1965-63, 220SE 1965-63, 230 1976-74 1969-66, 230S 1967-66, 230SL 1966-65, 240D 1976-74, 250 1972-68, 250C 1972-70, 250S 1967-66, 250SE 1967-66, 250SL 1968-66, 280S 1971-68, 280SE 1972-68, 280SEL 1971-68, 280SL 1971-68, 300SEL 1969-68 1965
Features & Benefits
- Pistons are durable, resistant to cracking or pitting and handle great loads.
- Rubber seals are replaced with new high temperature EPDM rubber for extended life and optimum performance.
- Mounting bracket is included where applicable for a hassle-free installation.
- Calipers are treated with a special formulated rust inhibitor and kept in the original equipment finish.
- New banjo bolts are included where applicable to ensure a perfect fit and quick installation.
- New bleeder screws provide trouble-free bleeding and a positive seal.
- New washers are included where applicable for a proper seal.
- A plastic cap plug protects every brake port thread to ensure trouble-free installation.
- New stainless steel hardware clips and new mounting pins are included where applicable.
- As a remanufactured Original Equipment part, this unit guarantees a perfect vehicle fit.
- Our remanufacturing process is earth-friendly, as it reduces the energy and raw material needed to make a new part by 80%.
Caliper, Brake Caliper, Disc Brake Caliper, Unloaded Caliper, Unloaded Brake Caliper, Power Brake Caliper, Hydraulic Disc Brake Caliper, Brakes
Product Attributes
| Inlet Port Size | 0.39 |
| Piston Quantity | 2 |
| Piston Material | Steel |
| Package Contents | Caliper; Instruction Sheet; Hardware Kit |
| Bleeder Port Size | M8x1.25 |
| Brake Caliper Finish | Oil Emulsion |
| Installation Hardware Included | Yes |
| Pads Included | No |
| Mounting Bolts Included | No |
| Product Condition | Remanufactured |
| E-waste | No |
| Piston Size (OD) (mm) | 56.90 |
| Piston Size (OD) (in) | 2.240 |
| FAQs | What type of grease is used on floating caliper mounting pins? |
| Features and Benefits | Rubber seals are replaced with new high temperature EPDM rubber for extended life and optimum performance. |
| Caliper Color | Gray |
| Abutment Clips Included | No |
| Anti-Rattle Spring Included | Yes |
| Bleeder Screw Included | Yes |
| 9559 | 1 |
| Bracket Included | No |
| Caliper Casting Material | Cast Iron |
| Caliper Color | Gray |
| 9611 | Oil Emulsion |
| Caliper Slides Included | Yes |
| Caliper Type | Floating |
| Casting Number | ATE |
| Grade Type | Regular |
| Inlet Fitting Type | Inverted Flare |
| 9544 | M10x1.0 |
| Mounting Bolt Included | No |
| Mounting Bracket Included | No |
| Mounting Hardware Included | Yes |
| Mounting Hole Diameter | 12.54266 MM |
| Mounting Hole Diameter | 0.494 IN |
| 9543 | 12.54266 MM |
| 9543 | 0.494 IN |
| Pad Wear Sensor Included | No |
| Pads Included | No |
| 7609 | 56.896 MM |
| 7609 | 2.24 IN |
| Piston Material | Steel |
| Piston Quantity | 2 |
| Bleeder Screw Cap Included | No |
| Rust Resistant Coating | Yes |
| Dust Boots Included | Yes |
| Bleeder Thread Size | M8x1.25 |
| Inlet Port Size | 10.00366 MM |
| Inlet Port Size | 0.394 IN |
| Contains Electronic Components | No |
| Does it require SDS | No |
| Is Item A Chemical | No |
| Is Or Contains A Battery | No |
| Is Or Contains A Bulb | No |
| Is Prop Sixty Five Affected | No |
| Is the item CARB affected | No |
| FAQ_Q1 | Can I switch out a Phenolic Piston Caliper for a Steel Piston Caliper or vice versa? |
| FAA_A1 | Not recommended. The O.E. manufacturers specified steel or phenolic pistons based on the intended use of the vehicle. It is recommended that the installer follow the manufacturer’s recommendations. |
| FAQ_Q2 | What type of fluid should I use: DOT 3, DOT 4, or DOT 5? |
| FAA_A2 | As a rule, always use brake fluid recommended by O.E. The fluid type is stamped on the master cylinder reservoir lid. Always use new fluid in a sealed container. |
| FAQ_Q3 | Car pulls to one side during braking. Why? |
| FAA_A3 | Inspect both calipers for binding or sticky slides or pins. Also ensure that brake hoses are not collapsed or restricted and inspect steering/suspension components for proper operation. |
| FAQ_Q4 | Brakes squeal all of the time. What's causing the squeal? |
| FAA_A4 | Brake squeal can be caused by improper installation of the brake pads, improperly installed brake hardware and improper brake rotor finish. |
| FAQ_Q5 | Could calipers be the cause of a low brake pedal? |
| FAA_A5 | A symptom of a low brake pedal is usually caused by air in the system, misadjusted rear brake shoes, deteriorated brake hose(s) or a defective master cylinder. |
| FAQ_Q6 | What type of grease is used on floating caliper mounting pins? |
| FAA_A6 | A silicone grease is used on floating caliper mounting pins. |
| FAQ_Q7 | Do all of your Calipers come with the new hardware and a mounting bracket for installation? |
| FAA_A7 | New hardware is included with all of our Calipers however the mounting bracket is an added option depending on part number and application. Mounting Brackets are also sold separately for most applications. |
Additional Information
| Remanufactured Part | Y |
| Warranty Distance | 24000 |
| Warranty Distance UOM | DH |
| Warranty Special UOM | TX |
| Warranty Time | 24 |
| Warranty Time UOM | MO |
| Country of Origin (Primary) | US |
| Harmonized Tariff Code (Schedule B) | 8708300050 |
| Harmonized Tariff Code (HTS) | 8708305090 |
| Canadian Harmonizing Tariff Code | 8708309920 |
| UPC | 00082617014458 |
Part Interchanges
Fits Vehicles
- Mercedes-Benz 250 (1968-1972)
- Mercedes-Benz 220Sb (1963-1965)
- Mercedes-Benz 250SL (1966-1968)
- Mercedes-Benz 250SE (1966-1967)
- Mercedes-Benz 200D (1966-1968)
- Mercedes-Benz 300SEL (1965, 1968-1969)
- Mercedes-Benz 220S (1963-1965)
- Mercedes-Benz 200 (1966-1967)
- Mercedes-Benz 250S (1966-1967)
- Mercedes-Benz 230SL (1965-1966)
- Mercedes-Benz 280SL (1968-1971)
- Mercedes-Benz 280SEL (1968-1971)
- Mercedes-Benz 220SE (1963-1965)
- Mercedes-Benz 280SE (1968-1972)
- Mercedes-Benz 280S (1968-1971)
- Mercedes-Benz 250C (1970-1972)
- Mercedes-Benz 230S (1966-1967)
- Mercedes-Benz 220D (1968-1973)
- Mercedes-Benz 190DC (1963-1965)
- Mercedes-Benz 220 (1968-1973)
- Mercedes-Benz 190C (1963-1965)
- Mercedes-Benz 230 (1966-1969, 1974-1976)
- Mercedes-Benz 240D (1974-1976)
A-1 Cardone Ind.® is a leading manufacturer and distributor of automotive parts and accessories, including master cylinders, clutches, calipers, and other braking system components. Its comprehensive range of products is made using the highest quality materials and the most advanced technology to ensure reliable performance, safety, and reliability. The company traces back its roots more than 35 years ago when Michael Cardone, Sr. remanufactures his first product: the windshield wiper motor. From then on, the name A-1 Cardone has been a go-to brand of automotive enthusiasts and fleet owners when it comes to new and remanufactured products that offer not just reliability but also long-lasting service.
California Proposition 65 Warning
California Proposition 65 Warning
Don't know your part number?
Take a photo and we'll identify it!
